VIM

salve tutti sono ancora io! volevo verificare un dubbio che mi è venuto sulla comunicazione seriale. come ho già scritto in un precedente post sto costruendo un cubo led 8x8x8. per comandare l'accensione diretta dei led uso arduino, mentre per decidere quali led utilizzare uso un programma in c# scritto da me. tramite quest'ultimo io ho la possibilità di creare le animazioni grazie all'interfaccia grafica. in particolare creo frame per frame e li concateno uno dietro all'altro per poi salvarli in un file. in sostanza l'idea era quella di passare un frame per volta ad arduino in modo che lui lo accendesse. io passo quindi una riga per volta (8 byte) di una matrice tridimensionale che rappresenta appunto il mio frame. il codice del ciclo è qualcosa de tipo: code: [select] for (z = 0; z < 8; z++) {        for (y = 0; y < 8; y++)         {                  for (x = 0...

is there easy way convert templates created in dreamweaver6 templates used in dreamweaver8 along documents templates attached to? is there need to? i noticed dreamweaver8 uses different syntax templates - editable regions - , i'd update currrent templates created in dreamweaver6. thanks > there need to? no. markup same. > noticed dreamweaver8 uses different syntax templates - > editable regions if seeing different markup template must have been created with earlier version of dw dw6. idea convert them, in case. find tutorial how here - http://www.dmx-templates.com -- murray --- icq 71997575 adobe community expert (if *must* email me, don't laugh when so!) ================== http://www.dreamweavermx-templates.com - template triage! http://www.projectseven.com/go - dw faqs, tutorials & resources http://www.dwfaq.com - dw faqs, tutorials & resources http://www.macromedia.com/support/search/ - macromedia (mm) technotes ================== ...

   okay working on project lm34dz  control digital pin on off attached to relay. have 3 different temperatures want relay on amount , off a different amount of time. have done delay's aware causes arduino to not process during these times.  know 1 solution use millis() , have see code can have independent on , off times post (listed below conditions). the temps , on/off times listed here temp>80°f relay on .5mins off 2.5mins temp>90°f relay on 1min off 2mins temp>95°f relay on 2.5mins off .5mins code unequal intervals http://forum.arduino.cc/index.php?topic=82777.0;wap2   code: [select] unsigned long currenttime = millis();   if (currenttime > nexttime) {     if (digitalread(pin)) {       digitalwrite(pin, low);       nexttime = currenttime + off_interval;     } else {       digitalwrite(pin, high);       nexttime = currenttime + on_interval;   ...

when open dw8 alert error states: the following translators not loaded due errors: following javascript(s) errors occurred: @ line 1266 of file "dante's ibook:applications:macromedia dreamweaver 8:configuration:shared:paypal:paypalshared.js": var re11 = /+/g; syntaxerror: invalid quantifier can tell me going on here? afraid of ruining files. need reinstall dw8??? please advise thanks. dante ps here link actual error code window here i solved problem. not sure how delete posting? More discussions in Dreamweaver support forum adobe

hallo zusammen, seit gestern habe ich meinen rasp pi 2 zu hause. ich habe gleich ein bundle gekauft, in dem zusätzlich kühlelemente vorhanden waren. das kleine kühlelement ist für den spannungswandler. leider ist mein elektrotechnik-wissen noch nicht stark ausgeprägt um diesen sicher zu erkennen. auch google bilder und youtube helfen nicht weiter. könntet ihr mir vielleicht helfen, sodass ich auch das letzte element aufkleben kann? vielen dank und viele grüße, klinggun https://www.raspberrypi.org/help/faqs/# ... ceheatsink der soc wurde für den einsatz in mobilen geräten entwickelt und benötigt daher keinen kühlkörper. auch die anderen teile benötigen keinen. dabei handelt es sich nur um optisches tuning raspberrypi

hi, clear ... my front page strictly 3 top user mods, positions 5, 6, 7. utilize no right or left positions except 1 empty right mod in order 'clear' formatting. each mod has same height of 1555px in css. i want add mod 8 & 9 (side side) under mod 6 @ 800 px down. so mod 6 height shortened allow 8 & 9. what don't know how write, or borrow matter, index.php code create these tables? [url=http://[/url]of other form of layout. so, this: _____5_______|***** manual signatures not allowed *****|_______7______| _____5_______|____8____|___9_____|_______7______| i have looked using footer , or going righ , left still need the index.php code implement regardless. any hugely appreciated. you can visit site without 8&9 here: [url]http://www.godekalb.com][/url]of other form of layout. so, this: _____5_______|***** manual signatures not allowed *****|_______7______| _____5_______|____8____|___9_____|_______7______| i have looked using footer , or going righ , left still need ...

i can't figure out why "for" loop wrote in code isn't working. it's supposed create number of mc instances (lowering each 1 20 pixels each time), seems though 1 keeps getting created. following link (only 8kb) has flash file along supplemental xml file (put in there avoid errors when testing movie): http://al-i.anixter.com/temp/flash_template.zip if please @ this, i'd appreciate it. it's small amount of code, shouldn't confusing or anything. thanks!... would paste code? don't run version of flash posted from. More discussions in Adobe Animate CC - General adobe

hi, hope i'm not barking wrong (forum) tree here, i thinking how make foldable cubicle... recall seeing kind of material rather loose, becomes stiff when voltage applied. has seen this? available ($$$...) mere humans? any other ideas in regards project welcome indeed - in advance! muscles - tighten right when voltage applied! maybe air mattress kind of thing. pressurize air, let out when want put away. no need keep blowing air once full. Arduino Forum > Topics > E-Textiles and Craft > Is there a material that goes stiff when voltage is applied...? arduino

will postseason.tv mlb work in intrpid ibex? i'm wondering whether should able watch, in case using mozilla firefox , adobe flash player. issue fact i'm still using gutsy gibbon. yea, yea, know, should upgrade os, i'm waiting until new hard drive. plus, machine use science research , can't afford have work issues new os right now. few weeks ago purchased view remaining season of on mlb.com, and, unfortunately, not view games under current os. bummer. last year had mlbviewer working. adobe page says have version 9.0.159.0 installed. guess spend $9.95 , take chances. can boot under windoze , watch there (just can't work @ same time). surprises me if mlb.com uses adobe flash, why not view games. got black screen , nothing else. mike Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Multimedia Software [ubuntu] post...

in project need measure data sensor , process arduino, have transfer data other device. what difference b/w above mentioned shields if wanted use them ? thanks in advance. hi, have few experience arduino might help. first, device want send data collect sensor, if going send computer recommend bluetooth transceiver, faster, easier , cheaper others shields mention above. another option using xbee more expensive , need two, 1 arduino , other pc receiving data (also need adapter xbee-usb), prefer option on bluetooth because xbee better , has lot of options , configurations bluetooth , can communicate lot of devices in same mesh. anyway try explain shields mention: ethernet shield/wifi shield: wired/wireless network adapter, can send data trough telnet (tcp sockets) device connected trough telnet too, or can use arduino web page server , show in web page data collected sensor gsm shield: acts mobile phone, can send/receive sms (text messages) , make/receive ca...

hello, we having problem natural language search on robohelppro within roboengine. since roboengine support iis , our client requires use sun 1 webserver, have configured reverse proxy , pass through requests help. works great except 1 thing. when access nls , enter text phrase search, doesn't return. appears roboengine , iis unable respond back, times out error. on actual server roboengine installed works fine. question trying answered how search working. when press search button, request getting posted , how roboengine communicating browser? information hoping further understand how configure our environment. search not responding same way when click on page help, because has generate list of found items , serve browser. understanding appreciated. joe blasko More discussions in RoboHelp adobe

after has been written on floats, have still been having trouble in multicolumn situation because when try clear images , divs in second column (right column) left clears, clear introduces gap in right column down end of left column. have tried techniques written in gallant , bergevin's tutorials without success, either have other problem in conflict, or missing something. furthermore, when try hack overcome 3 px ie problem, dreamweaver 8 design window falls apart, curiously firefox , safari browsers (mac osx) not show problem. floating content div doesn't seem work right. the page in question can found @ http://cabrackett.com/bella_galleria/the_gallery.html it looks in browsers have again has been hacked adding   add white space want use clear for. chuck change section of code below this. page and css first can if needs revert. <p><img src="the_gallery_files/cabrackett_20060421_5963-m.jpg" alt="the gallery" width="478" heigh...

hi have been trying lately use raspberry pi control 1mhz oscillator on raspberry pi don't have ideas on how make work.. have been creating python tkinter gui nice controller layout. computer controlled transmitter has been done before on computer using old 9 pin connector ( http://sci-toys.com/scitoys/scitoys/com ... itter.html ).. think work on respberry pi well, gpios. ideas/suggestions? keep working on it.. scratch nice tool on well, try that. btw cool, transmitter uses morse code transmit message , oscillator on machine can recieve , decipher using programm, text machine works in range of 8km.. if without interference. what mean control oscillator? can use clocks or pwm peripheral generate 1mhz clocks on various gpios. can't modulate signal. raspberrypi

hello everyone: the other day bought embedded artists' 2.7 inch e-paper displays ( http://www.embeddedartists.com/products/displays/lcd_27_epaper.php ). looks great project , love use in it. since or rest of project requires arduino yun, hook display it. in order that, tried use same wiring embedded artists provided uno ( http://www.embeddedartists.com/sites/default/files/support/displays/epaper/epaper_arduino.pdf ). however, nothing happens... when doing internet research found out other epaper boards have different wirings uno , leonardo (which knowledge equal yun exept lack of linux parts). example: http://repaper.org/doc/extension_board.html for lenoardo seem use icsp pins - uno not. do have idea how wire display arduino leonardo or yun? love use display may project... thanks, stefan ok, went through pints , meaning. got work!!! wooohooo! well @ least example can found at: http://www.embeddedartists.com/products/displays/lcd_27_epaper.php . thi...

i'm using 20150609-raspbian-wheezy-nox.img set in config previous: code: select all dtparam=i2c=on1=on dtparam=spi=on , code: select all vcdbg log msg show me: code: select all 001923.431: dtparam: i2c=on1=on 001923.875: unknown param 'i2c' - ignored 001923.897: dtparam: spi=on 001924.339: unknown param 'spi' - ignored other dtparams work fine. sec, i'll see if same thing. edit: i've flashed image , enabled i2c using raspi-config. no issues here, phil taking @ well. pastebin entire config.txt? raspberrypi

hello i quite sick , tired of volatile sef applications. if place standard url within server soley redirect joomla page , use index within search engines work? i want dodge huge server strain, have standard sef working it`s not enough so, work? depends on redirect method. types allow search engines consider static page correct url (eg. mod_rewrite approach, internal redirect) whereas others transfer requests joomla site , let search engine know has been redirected (eg. meta redirect in static page). what problems having sef extensions? run number of busy sites both artio , opensef (not on same sites, obviously... :-) ) , have found performance , stability of both good. run number of caching strategies assist reducing server load - see link in signature faq on use increase performance. Board index Joomla! Older Version Support Joomla! 1.0 General Questions - 1.0.x

buenas compis! estoy intentando utilizar un arduino due como slave para poder leer valores dmx512. he estado buscando placas y parece que todas son para arduino uno y 5 v de trabajo. el circuito de dmx protejido no es mucho problema. pero las librerias son otro cantar...  alguien que pueda arrojar un poco de luz? en el foro guiri parece que llevan mas de un año con el tema y sin solucion  os dejo el link con un esquema bastante decente de conexion dmx (el priblema esta en que es para ardu 1 y que trabaja obviamente 5 v) http://www.mathertel.de/arduino/dmxshield.aspx lo dicho, si alguien puede hechar un cable seria "most apreiated" xd saludos, por otro lado tambien esta la posibilidad de utilizar una placa para dmx y utilizar el puerto de comunicaciones i2c. pero tampo encontrado placa alguna  =( tal vez, juntando un arduino uno con placa dmx y enviarlo todo via i2c al due... en cuanto tengas mas info informo ver si alguien se anima...

hi, tried frugal installation of ubuntu (ie, install root fs as-is without expanding) failed. i've been doing: copy /casper cdrom onto usb pen, add boot entry following grub: code: title try ubuntu without change computer kernel /casper/vmlinuz boot=casper initrd /casper/initrd.gz this approach has been working other linux distros used, debian-live, grml, slax family, puppy linux, etc. why casper make complicated? ubuntu 9.04. symptom that, vmlinuz , initrd.gz found expected, casper fails when trying mount sqausfs root: why screen shot lost, 2 times? trying 3rd time. . . Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Installation & Upgrades [ubuntu] casper is over complicated Ubuntu

hejsa jeg har et lille problem med det modul der hedder ultimate ajax newsflash det kan ikke vise danske bogstaver , altså Æ Ø Å    jeg har læst lidt rundt omkring om dette problem og er blevet lidt forvirret ang forskellige løsninger af dette  er der nogle af jer der selv bruger dette modul og har fundet en løsning der virker ? der er bla en løsning der hedder @ man skal tilføje sin isocharcet kode .htaccess file, men hvad er den danske kode dette ? venlig hilsen alex der er generelt et problem med danske tegn og de løsninger der bruger ajax. problemet er @ ajax ofte leveret outputtet utf-8 tegnsættet. det skriver de også selv om deres produkt. - fixed issue of international characters not displaying correctly, in title of content item. output of module utf-8. så det du skal gøre er @ lave din side om til @ levere output ren utf-8, og det er ikke helt let. hvis du læser denne post, http://forum.joomla.org/index.php/topic,50934.0.html vil du se @ du kun kan nærme dig r...

i've been helping uncle recent software updates. recently, renewed norton internet security subscription (for 2 years) , got free copy of systemworks out of deal. around same time, msn updated browser , connection software (he's on msn dial-up). ever since, flash hasn't been working. had 7, thought needed update. going flash 9 install page failed work. through msn browser, no activex control security dialog happened. did clean uninstall of flash , able security dialog. didn't help, since no download box came up. so, came home. on computer downloaded install_flash_9 msi package, burned cd , installed on computer. when go site has flash, still shows box x. can right click on , "about" "settings" , "about flash 9" options, nothing there helps. i searched on msn's settings, haven't found block flash. tried temporarily disabling norton, didn't either. his computer slow because has million spyware blockers , popup blockers, did m...

hi, installed xubuntu on pc. installation set resolution 1280x800. changed 1024x768, change did not persist after reboot, went 1280x800. when install ubuntu on same pc dont have problem. change 1024x768 stays there. problem xubuntu. want work xubuntu pc old , weak ubuntu . how can fix problem? thank you donescamillo i have same problem, , seems others have been well: (check out links) able find quick , dirty workaround install, specific fluxbox . may able adapt xfce ... http://ubuntuforums.org/showthread.p...+problem+reset i added line: code: xrandr -s 1024x768 to ~/.fluxbox/startup file few other possible solutions: it seems many people updating video drivers , or editing xorg.conf file helped... http://ubuntuforums.org/showthread.p...+problem+reset or trying this command in terminal: code: sudo dpkg-reconfigure xserver-xorg http://ubuntuforums.org/showthr...

salut à tous! j'aimerais avoir votre avis (étant peu expérimenté et pas trés à l'aise avec l'electronique) sur la direction que je prend pour réaliser mon projet. je souhaite obtenir un tension 12v alternative dont je puisse faire varier ça fréquence avec un potentiomètre en partant d'une tension de batterie classique 12v. j'ai fait un shéma vite fait  pour essayer de vous montrer ma démarche. la grande question est! esque je mis prend bien ou je me met le doit dans l'oeil jusqu'au coude?  il n'y pa tout les éléments sur le shéma mais c'est cette partie la plus importante. petite explication: je compte générer deux sinusoide avec les pwm de l'arduino pour commander deux mosfets qui sont alimentés par une alimentation symétrique. je ne sais pas du tout si les diodes sont vraiment utiles mais bon au cas ou... :~ ca me parait un peut simplet comme systeme quand même, de plus j'ai besoin de pas mal d'ampere en s...

i need embed mpg file php page... it's supposed 380x425, video guy couldn't figure out how export non-standard dimensions. i've tried resizing within code, keeps playing @ dimensions specified. help!! this code i'm working with: function mympg() { document.write('<embed src="cuts.mpg" controls="imagewindow" width="380" height="425" autostart="true"> </embed> } <embed src="cuts.mpg" controls="imagewindow" console="video" width="380" height="425" autostart="true"> </embed> jasper24 wrote: > need embed mpg file php page... it's supposed 380x425, > video guy couldn't figure out how export non-standard dimensions. > i've tried resizing within code, keeps playing @ > dimensions specified. help!! > > code i'm working with: > > function mympg() > { > document.write('<embed src=...

i have dhcp server on windows server 2008 r2 machine configured hand out reserved ip addresses specific mac addresses. have used number of pib , pi2b machines, among others. ran apt-get update/dist-upgrade move 05-05 release on couple of machines, , no longer reserved addresses. in 1 case, isn't huge problem (although inconvenient) because there monitor attached (actually pitft, show ip address). in second case less convenient, since headless. examining udp packets, there appears additional data mac address forming identifier in dhcp request. configuration option somewhere can change , restore original behaviour? ok, found it. in /etc/dhcpcd.conf there section turns on 1 or other of options clientid or duid identifier. clientid option apparently off default, mac address, , duid option on default, mac address, prefixed "random" 8 bytes of data, shown in /etc/dhcpcd.duid quick edit of config file , reboot, , "all once was", guardian in "the city...

hi , using zte mf667 , want connect rpi install wvdial , configure wvdial.conf >>> [dialer 3gconnect] init1 = atz init3 = atq0 v1 e1 s0=0 &c1 &d2 +fclass=0 init4 = at+cgdcont=1,"ip","mobinilweb" stupid mode = 1 modem type = analog modem isdn = 0 phone = *99# new pppd = yes modem = /dev/ttyusb1 username = { } password = { } baud = 9600 , /etc/network/interfaces >>> auto lo iface lo inet loopback iface eth0 inet static address ********** netmask ********** network ********** broadcast ********* gateway *********** allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp , ifconfig >> eth0 link encap:ethernet hwaddr b8:27:eb:68:fe:12 broadcast multicast mtu:1500 metric:1 rx packets:167 errors:0 dropped:0 overruns:0 frame:0 tx packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:...

i planning on creating gps tracker displays location on map , shows movement(refreshes every 5-10 seconds) gps data received on vhf transmission on select frequencies (151,820 mhz, 151,880 mhz, 151,940 mhz, 154,570 mhz, 154,600 mhz). have tft screen display. father hunter , uses dogs. tracks them gps collar. has handheld device difficult hold, , @ device while driving. reason being runs roads protect dogs danger when crossing highways , such. if give me idea on how receive gps data sent on vhf signals , put them gps format map, want add gps tracker in vehicle shows on display. links/parts/or advice appreciated. (i have looked through forums , online couldn't find related vhf receiving) thank you. would software work on raspberry pi? http://ravtrack.com/gps-software-downloads raspberrypi

username: password: i forgot password resend activation email remember me hide online status session   register in order login must registered. registering takes few moments gives increased capabilities. board administrator may grant additional permissions registered users. before register please ensure familiar our terms of use , related policies. please ensure read forum rules navigate around board. terms of use | privacy policy register raspberrypi

just got kbell engineering on ebay, w5100 ethernet shield, advertised mega compatible.  recommend mega 2560 users because: 1. pins correct length seat icsp plug fully; 2. has separate reset resets shield , not both; 3. can remain in place during uploads of code, doesn't interfere uploads other w5100 shield does; 4. has leds power, link, 100m, fulld, coll, tx, rx. cost $12.00 on ebay , ships usa.  superior others mega users. Arduino Forum > Using Arduino > Networking, Protocols, and Devices (Moderator: fabioc84) > KBell Engineering Wiznet W5100 ethernet shield mega compatible arduino

we have copy of contribute. told create pdf files on fly - - when tried got error message saying needed have adobe 8 pdf creator. more expense expensive project. can create web page excel or word , want know how link page in contribute. can please ? many thanks, gypsygranny More discussions in Contribute General Discussion adobe

the layout of design done bg images in div tags. works fine except in ie 6. in browser top right , top left corner bg images not show up. suggestions? here's link page: http://www.jesseyoung.com/baker/ here's link css: http://www.jesseyoung.com/baker/styles.css thanks... -jesse change in css each background image from: background-image: url(images/bg.jpg); to: background-image: url(../images/bg.jpg); hth, --nancy o. alt-web design & publishing www.alt-web.com "jessely" <webforumsuser@macromedia.com> wrote in message news:fvam58$8c7$1@forums.macromedia.com... > layout of design done bg images in div tags. works fine > except in ie 6. in browser top right , top left corner bg images > not show up. suggestions? > > here's link page: > http://www.jesseyoung.com/baker/ > > here's link css: > http://www.jesseyoung.com/baker/styles.css > > thanks... > > -jesse > > > More discussions in D...

i have simple flash movie. it has static image(show screen), click on upper right invisible button goes next frame(video), flvplayback component playing , h.264 mov file. if movie finishes sends final static image (park screen). works fine swf, when goes out projector shows black screen video , loses both next , prev invisible buttons in either upper corner navigation. crashes projector. i have tried many different ways set fullscreen properties , nothing seems work longer, see commented out stuff in frame 1. how can make play simple movie fullscreen, projector, h.264 video? my example file located here: http://www.bigpictureimaging.com/fullscreenprojectorwh264help.zip tia palnudb simple question, in code loading swf file (skinoverplayseekstop.swf) , calls video file ? we don't see ? regards flashjester support team e. - support@flashjester.com w. - www.flashjester.com "this has been 1 of impressive , thoroughly pleasant experiences of customer support have ev...

http://www.studio10webgraphics.com/internetposts/pcstest/assets/html/contact_us.html above link page have placed div in 'main content area. div colored can see it's size okay, has 2 floated text columns work fine. problem is, container text columns not go in main content area higher bottom of side bar on left side of page. i have client coming town wants see working , stuck because knowledge of how fix div container exhausted. can here tell me how fix this? appreciatively, ken nielsen More discussions in Dreamweaver support forum adobe

remember blog post 2013? https://www.raspberrypi.org/amazon-drones-hax0r3d/ samy kamkar managed hack ar drones using pi? has devised algorithm hack masterlocks in @ 8 tries. http://arstechnica.com/security/2015/04 ... s-or-less/ soon, there algorithm doing anything raspberrypi

dear all, good morning 1. pin 12 set button pin input command reset delay 10sec. after button press reset . thanks, eduard  what ? do expect know talking ? try posting code (use code tags button "#" !) Arduino Forum > Using Arduino > Project Guidance > Please Help, Reset by Program Command in Button with delay. arduino

hey, i have wide flash page, main portion of in center of .swf. question how make center of .swf in center of web browser when user resizes browser, center of stage stays in center of browser? right has left side of .swf aligned left edge of browser center of .swf being cut off the right edge of browser , users have scroll right see main portion of site...i'm sorry if that's confusing, at appreciated. thanks! dave hi, try following code in css file - #wrapper { margin: 0 auto auto auto;} where #wrapper id of main div tag in body of html page. also, write body {text-align:center;} in css file , try it. gaurav www.gauravchandra.com More discussions in Dreamweaver support forum adobe

i want upload files in folder on server user selected in combobox. cant working, ideas? in flex: private function startupload():void { if (_arruploadfiles.length > 0) { disableui(); listfiles.selectedindex = _numcurrentupload; scrollfiles(); // variables send along upload var sendvars:urlvariables = new urlvariables(); sendvars.projekt = combobox(projektnamn).selecteditem.data; var request:urlrequest = new urlrequest(); request.data = sendvars; request.url = _struploadurl; request.method = urlrequestmethod.post; _refuploadfile = new filereference(); _refuploadfile = listfiles.selecteditem.file; _refuploadfile.addeventlistener(progressevent.progress, onuploadprogress); _refuploadfile.addeventlistener(event.complete, onuploadcomplete); _refuploadfile.addeventlistener(ioerrorevent.io_error, onuploadioerror); _refuploadfile.addeventlistener(securityerrorevent.security_error, onuploadsecurityerror); _refuploadfile.upload(request, "file", false); } } ...

i having problem getting ubuntu manage screen brightness. seems change if come out of standby without being plugged in can't change dynamically. have tried adding noapic option in boot line in menu.lst didn't help. not sure next troubleshooting. using hp/compaq 8501w. i still looking on issues. suggestions on where/how start troubleshooting? Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Hardware [ubuntu] Screen Brightness Control Ubuntu

i've got old ibook g3 (900mhz) i'd run flavor of ubuntu on. i've installed ubuntu , xubuntu @ various times, suffered system freezes, etc. re-installed os x , ran memtest, caused kernel panic. pulled 512mb chip, , ran again, same result, guess it's safe ram on motherboard bad. i've read online, there's no fix on os x side short of motherboard replacement, , computer's not worth expense, @ point. i'm wondering though, ubuntu-newbie, there way once have ubuntu installed can tell ignore ram on motherboard? 512mb alone ought @ least run xubuntu comfortably, yes? Forum The Ubuntu Forum Community Ubuntu Specialised Support Apple Hardware Users [all variants] Disable on-board RAM on iBook G3? Ubuntu

i know there live demo cds default installs of 1.0.11 , 1.5beta there way put established 1.0.11 site on memory stick or dvd (not sure cd big enough)? i'd demo site on laptop in locations no internet access. rsphaeroides wrote: i know there live demo cds default installs of 1.0.11 , 1.5beta there way put established 1.0.11 site on memory stick or dvd (not sure cd big enough)? i'd demo site on laptop in locations no internet access. this 1 have been 1 search (i know don't think search feature useful - have given lots of useful information in case) http://forum.joomla.org/index.php/topic,20457.msg221191.html#msg221191 regards dave Board index Joomla! Older Version Support Joomla! 1.0 General Questions - 1.0.x

dear all, i interested use ardunio board. primarily, require serial interface level transceiver (i.e. on board ttl-232 interface). 2 or more serial interfaces level transceivers preferred. board may have usb, ethernet , other interfaces (as added advantage). i have searched ardunio product list. unable find board on board ttl-232 interface. help appreciated. regards, thanks. a.z.deen quote from: azdeen on jun 11, 2014, 10:01 am i have searched ardunio product list. unable find board on board ttl-232 interface. and not think find nowadays. three plenty of add-on modules this. Arduino Forum > Using Arduino > Project Guidance > Any Arduino board with TTL-232 interface (level transceiver)? arduino

i'm toying around idea in head: grew in 80s, type-in code different computer magazines such 80 micro, , compute! days (kind of) over. , raspberry pi came , planted question in brain: suppose there e zine available targeting raspberry pi users low income (say house income of less $20,000 year) , e zine includes type in code games, utilities , other useful programs (such word processor) diy projects involving found objects, or trip store no more $20 in pocket. articles , projects written similar users invitation other low income users submit code , projects. goal of zine promote innovation , original thinking without having spend entire fortune. such zine exist? you mean have never heard of magpi? professionally made magazine pi, , electronic version free. #35 out! viewtopic.php?p=780935#p780935 raspberrypi

i have done basic programming pic , basic stamps , having fun arduino uno.  have project , advice optimal arduino project.  have simple tv antenna (aluminum) on aluminum mast rotor runs on 12vdc (solar charged deep cycle batteries) control remotely in-house while monitoring antenna compass heading in real time .  set heading desired , have controller activate rotor motor until heading reached.  have figured out basics of uno reading data lcm303 magnetometer, , have xbee series1 connected uno transferring corrected compass heading data via serialsoft.h library xbee connected laptop.  for remote project, @ antenna side, envision local arduino+mag sensor+servo relay shield+xbee.  150' away have arduino standalone controller + xbee+graphics lcd.  (to start though have xbee laptop software control). for remote location setup, uno or due adequate handle xbee serial interrupt communications sending magnetometer data strings, , receiving servo m...

bonjour, je suis actuellement en train d'essayer de communiquer par rs485 via un shield avec un capteur uhf. mes commandes de trigger ne font pas d'effet sur le capteur, aucun bip du capteur.  sur le serial je récupère en permanence des informations en continues comme : code: [select] 56 4d a3 25 0 4f d2 b 8d ad 0 0 b3 32 0 65 b3 32 0 65 b3 32 0 66 b2 33 0 67 64 67 66 66 b3 32 0 65 67 66 66 67 65 b2 b2 33 0 b3 32 0 59 de 1e 0 65 b2 bb 3 0 d7 eb 65 1 0 db 3 0 65 fb 3 0 bb 3 0 ae bb 6d 1 0 db fd 1 0 ec b 0 eb dd fd 1 0 f6 fb 3 0 db 65 1 0 cb 3 0 fb 65 65 b3 9b 65 cb b3 9b b2 cb 66 9b 64 d9 64 b2 b2 65 cb b3 9b 9b 9b b2 b2 64 9b 65 db cb 66 fb 65 alors que je souhaiterai recevoir des informations plus cohérentes et non en continues du même type que sur le logiciel constructeur, qui sont des informations tag scannées  : code: [select] <ff><ff><fb><00><3f><41><10><00><00><01><10><01><00...

hi hope can me. i have joomla site (v. 1.11 upgraded): http://www.vitalbmx.com intermittently no reason figure out, page title: vitalbmx.com - vital bmx - source bmx videos, bikes, news, pictures, , community will change simply: vitalbmx.com - home i can't figure out why happening. have other sites not yet upgraded joomla 1.11 (joomla 1.10) same thing happening. don't think it's related joomla 1.11 upgrade. this huge deal because we're falling off google ranking due lack of complete page title. what's weird there seems no predictability this. title there, it's not. any @ appreciated. hello, do have sef patch installed? if not solve problem (i think): http://extensions.joomla.org/component/ ... itemid,35/ Board index Joomla! Older Version Support Joomla! 1.0 General Questions - 1.0.x

after wrestling bad install , connecting different hdmi display startx opened doesn't show menu bar @ top , trash bin , icon below flicker. if use sudo startx display normal. created new user , display normal too. have looked @ various lxt..... folders in .config pi , new user , amended pi 1 match new no avail. problem setting or settings @ user level. noob rpi (version 2) , unfamiliar linux way of doing things. being pi user real backward step have start scratch setting various python servo control routines. ideas how can trace issue? appreciated. raspberrypi

i made new website. , want text centered on top of content box. content box has image have set <td background="contentbox.jpg"> .. text comes on content box image http://img469.imageshack.us/img469/6753/untitled1kk6.jpg in screenshot text (circled) comes in middle of image , want centered on top of content box x is.. how do that? if can post code or link actual page, help More discussions in Dynamic HTML General Discussion (read only) adobe

salve tutti, mi sono appena iscritto. ho 2 raspberry ed un notebook con win7 messi su uno switch. un raspberry con debian che fa da server ed un altro con noobs. per quanto riguarda windows uso putty come emulatore di terminale remoto. cosa devo usare su noobs per utilizzare un terminale remoto e accedere al debian? grazie per ventuali cortesi suggerimenti se usi noobs e hai installato raspian, menu --> accessori --> terminale e lanci ssh ssh utente@ip_debian se non fai il login grafico in lxde, il semplice terminale è sufficiente dopo che hai fatto il login con pi. raspberrypi

ho acquistato lo starter kit di arduino poco più di una settimana fa, ho svolto tutti progetti proposti dal libro e ne ho ideati altri di testa mia senza alcun problema con vari componenti, ma da oggi pomeriggio ho notato che gli interruttori non funzionano più e non riesco capirne il motivo. con il tester ho appurato che gli interruttori di per sé non hanno problemi: premendo il pulsante viene rilevata continuità tra due terminali; però quando li vado ad inserire nel circuito è come se non ci fossero. l'unica spiegazione che mi rimane è che terminali non fanno contatto con la breadboard, ma non riesco comunque spiegarmi come sia possibile che fino ieri non abbia avuto problemi mentre oggi nessuno dei 10 pulsanti sembra utilizzabile. se il problema è questo, come posso risolverlo e da cosa può essere stato causato? oppure quale altra spiegazione potrebbe esserci? ora tu per un attimo immagina di essere l'esperto e io ti dico che ho 10 pulsanti ca...

bonjour à tous, je suis nouveau sur le forum et dans l'utilisation d'arduino. j'ai un projet à réaliser et cela nécessite le contrôle de servomoteurs. je voulais savoir si cela était possible avec une kinect, c'est à dire que lorsque la personne se déplacerait de gauche à droite, le servomoteur effectuerai une rotation de gauche à droite et inversement. si ce n'est pas possible avec une kinect, avec quel autre matériel/logiciel serait-il possible de faire cela? je vous remerciement grandement pour vos réponse et l'aide que vous pourrez m'apporter. cela doit être possible avec la kinect mais ça risque d'être très lourd à mettre en oeuvre. sinon tu peux mettre 4/5 détecteur de présence infrarouge sur un demi cercle, ça te fait une barrière à 180°avec 4 positions pour les servomoteurs. après ça dépend de la précision que tu veux avoir pour les servos. solution un peu moins lourd que la kinect, tu des librairies de trait...

hey all, i've got triple boot setup running win xp, ubuntu 7.10, , win 7 rc. came xp, loaded 7.10, win 7 beta ->rc. using windows 7 boot manager of right now. have added menu entries in order grub boot ubuntu, i'm wondering if upgrade 8.04, lose windows boot manager , have replaced grub? believe there issue while ago grub wouldn't play nice win 7 why needed windows boot manager. i'm pretty new type of stuff, i've gone pretty far getting working triple boot. apparently, 7.10 eol , 8.04 next logical step. or insight appreciated! Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Installation & Upgrades [ubuntu] Upgrading 7.10 to 8.04; need help with GRUB and multiple OS Ubuntu

i logged in , wrote long post. interrupted few times time passed. got done , pushed 'preview' button. says need log in! , wrote found! that'll happen. happens private messages too. best advice have write longer posts in text editor application , post them when think ready. don't know how custom work goes forum, wouldn't take effort have small ajax requests keep session alive while user writing post/message. easy keep track of content of yet-to-be-posted message/post , transfer content new session not lost. raspberrypi

hi guys, i've managed connect 5 temp. sensors 1 bus using code: code: [select] /* yourduino multiple ds18b20 temperature sensors on 1 wire  connections:  ds18b20 pinout (left right, pins down, flat side toward you)  - left   = ground  - center = signal (pin 10):  (with 3.3k 4.7k resistor +5 or 3.3 )  - right  = +5 or +3.3 v   questions: terry@yourduino.com   v1.01  01/17/2013 ...based on examples rik kretzinger   /*-----( import needed libraries )-----*/ // 1-wire library here: http://www.pjrc.com/teensy/td_libs_onewire.html #include <onewire.h> //get dallastemperature library here:  http://milesburton.com/main_page?title=dallas_temperature_control_library #include <dallastemperature.h> /*-----( declare constants , pin numbers )-----*/ #define one_wire_bus_pin 10 //lcd #include <liquidcrystal.h> liquidcrystal lcd(12, 11, 5, 4, 3, 2); /*-----( declare objects )-----*/ // setup onewir...