Skip to main content

Thread: cannot get wicd and ndiswrapper to work together,

-

i installed linux 9.04 , updated fully, , installed 2 programs. wicd manager , ndiswrapper. installed rt2870.inf file in same folder beside .sys file. cant wicd show router, thats plugged in beside me. can see on windows, , connect not linux. also, have no clue how setup wireless interfaces, , such. but, can give me detailed step step guide on how internet working wicd , nidiswrapper, , usb wifi stick, ralink chipset, rt2870.inf driver, (extra details)?
i'm pretty new, hope it'll work alot guys, i'm sick of windows...
ifconfig -a
iwconfig
ndiswrapper -l results, here :
kyle@kyle-desktop

:~$ ifconfig -a
eth0 link encap:ethernet hwaddr 00:01:02:cd:3d:71
inet6 addr: fe80::201:2ff:fecd:3d71/64 scope:link
broadcast multicast mtu:1500 metric:1
rx packets:0 errors:0 dropped:0 overruns:0 frame:0
tx packets:3 errors:0 dropped:0 overruns:0 carrier:3
collisions:0 txqueuelen:1000
rx bytes:0 (0.0 b) tx bytes:228 (228.0 b)
interrupt:10 base address:0x4000

lo link encap:local loopback
inet addr:127.0.0.1 mask:255.0.0.0
inet6 addr: ::1/128 scope:host
loopback running mtu:16436 metric:1
rx packets:0 errors:0 dropped:0 overruns:0 frame:0
tx packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
rx bytes:0 (0.0 b) tx bytes:0 (0.0 b)

pan0 link encap:ethernet hwaddr 0a:c1:89:98:54:6a
broadcast multicast mtu:1500 metric:1
rx packets:0 errors:0 dropped:0 overruns:0 frame:0
tx packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
rx bytes:0 (0.0 b) tx bytes:0 (0.0 b)

kyle@kyle-desktop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.

kyle@kyle-desktop:~$ ndiswrapper -l
warning: config files need .conf: /etc/modprobe.d/ndiswrapper, ignored in future release.
rt2870 : driver installed
device (148f:2070) present
kyle@kyle-desktop:~$

are using x86 ubuntu or 64bit version? bearing in mind 32bit driver 99% not going work ndiswrapper in 64bit linux.

type lsusb terminal usb adapter plugged in. if says device , (no firmware) after it, point incorrect driver.

using ndisgtk (the gui version of ndiswrapper?) or typing commands youself;

i.e. ndiswrapper -i drivername
modprobe ndiswrapper

etc,etc?


if driver using correct , has been installed correctly ndiswrapper should see "wlan0" when type iwconfig terminal.


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] cannot get wicd and ndiswrapper to work together,


Ubuntu

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more