Problem uploading code on Arduino Leonardo

-

hello. need guidance on arduino leonardo, because whenever try upload code, have errors, or board isn't installing properly. found post yesterday: https://code.google.com/p/arduino/issues/detail?id=1033, similar problems.

ide version used: 1.0.5. os: windows 7, 64 bit.

1. uploading code failed first time. led l (load) off, power led on. ide not see com port ("serial port" option grayed , inactive). error:

code: [select]
processing.app.debug.runnerexception: couldn't find leonardo on selected port. check have correct port selected.  if correct, try pressing board's reset button after initiating upload.
at processing.app.debug.avrdudeuploader.uploadviabootloader(avrdudeuploader.java:153)
at processing.app.debug.avrdudeuploader.uploadusingpreferences(avrdudeuploader.java:67)
at processing.app.sketch.upload(sketch.java:1671)
at processing.app.sketch.exportapplet(sketch.java:1627)
at processing.app.sketch.exportapplet(sketch.java:1599)
at processing.app.editor$defaultexporthandler.run(editor.java:2380)
at java.lang.thread.run(thread.java:619)

2. hit 1 time reset button: load led blinks 5-8 seconds it's off; ide not see serial port.

3. device manager shows (i attached print screen): bootloader com port grayed (showed if hit hidden devices option) , arduino leonardo com port seen. ide still not sees com port. however, have ide version called "arduino erw 1.0.5", sees com port, without load led on, cannot upload code; error on ide:

code: [select]
processing.app.debug.runnerexception: serial port 'com3' in use. try quitting programs may using it.
at processing.app.debug.avrdudeuploader.uploadviabootloader(avrdudeuploader.java:162)
at processing.app.debug.avrdudeuploader.uploadusingpreferences(avrdudeuploader.java:71)
at processing.app.sketch.upload(sketch.java:1716)
at processing.app.sketch.exportapplet(sketch.java:1628)
at processing.app.sketch.exportapplet(sketch.java:1600)
at processing.app.editor$defaultexporthandler.run(editor.java:2471)
at java.lang.thread.run(unknown source)

i have been reading many posts on internet. way can upload code on board pressing reset button until message "uploading..." shows on ide, wait 2-4 seconds , release button. code uploads on board, load led still off.

my questions:

does board have problems on loading code?
do wrong?
how can work clean leonardo, without having problems when upload code?

thank you, appreciated.



Arduino Forum > Using Arduino > Installation & Troubleshooting > Problem uploading code on Arduino Leonardo


arduino

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more