Skip to main content

Thread: fstab is going to get stabbed!

-

ok observe this:

//127.0.0.4/ /media/kody ext3 defaults 0 0

wrong it? i've tried following....

//127.0.0.4/sda1 /media/kody ext3 defaults 0 0

//127.0.0.4/sda1/home /media/kody ext3 defaults 0 0

//127.0.0.4/home /media/kody ext3 defaults 0 0

, 10.0.0.4

, replacing ip server name......

don't anything, mount point have lower case, in k not k

i'm going go try other side, , make sure got ip right.......

have move 30 gigs of stuff xd

code:
root@kody:/home/kody# mount //10.0.0.6/sda1 /media/draco-laptop mount: wrong fs type, bad option, bad superblock on //10.0.0.6/sda1,        missing codepage or helper program, or other error        (for several filesystems (e.g. nfs, cifs) might        need /sbin/mount.<type> helper program)        in cases useful info found in syslog - try        dmesg | tail  or so
i know it's ext3 , when try:

code:
/home/kody# mount //10.0.0.6/sda1 /media/draco-laptop ext3 defaults 0 0
it spits out info mount command.......

, eth0 confirms kody designated 10.0.0.4

chance router problem?


, draco, prove i'm not crazy.....

code:
wlan0     link encap:ethernet  hwaddr 00:1d:d9:75:bb:b6             inet addr:10.0.0.6  bcast:10.0.0.255  mask:255.255.255.0           inet6 addr: fe80::21d:d9ff:fe75:bbb6/64 scope:link           broadcast running multicast  mtu:1500  metric:1           rx packets:910804 errors:0 dropped:0 overruns:0 frame:0           tx packets:638762 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            rx bytes:1229012354 (1.2 gb)  tx bytes:95329126 (95.3 mb)
.6! knew was.....

lets see, else should mention......


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [all variants] fstab is going to get stabbed!


Ubuntu

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more