Paramétrage liaison série 1 bit de start et 1 bit de stop

-

bonjour à tous,

pour l'évolution d'un projet, je dois me connecter via la liaison série avec un appareil communicant à 9600 bauds 1 bit de start; 8 bits de com et 1 bit de stop !!!

jusqu'à présent, je me connectais à des appareils en 4800 ,8 bits de com et 2 bits de stop avec le code suivant :

serial2.begin(4800, serial_8n2);

mais maintenant ????

merci d'avance pour vos réponses.

pierre


quote from: petrusfr on jun 15, 2014, 09:34 pm

bonjour à tous,

pour l'évolution d'un projet, je dois me connecter via la liaison série avec un appareil communicant à 9600 bauds 1 bit de start; 8 bits de com et 1 bit de stop !!!

jusqu'à présent, je me connectais à des appareils en 4800 ,8 bits de com et 2 bits de stop avec le code suivant :

serial2.begin(4800, serial_8n2);

mais maintenant ????

merci d'avance pour vos réponses.

pierre




bonsoir
maintenant c'est encore plus simple  :smiley-mr-green:
serial2.begin(9600) ;

les options 8n1 etant par defaut


Arduino Forum > International > Français (Moderators: jfs, Snootlab) > Paramétrage liaison série 1 bit de start et 1 bit de stop


arduino

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more