Skip to main content

Thread: have to keep disconnecting and reconnecting w/bcm43xx driver

-

i have keep disconnecting , reconnecting school's ap randomly (sometimes frequently, infrequently) on hp pavillion zv6000 running kubuntu 9.09 jaunty , using bcm43xx driver. (i couldn't work @ ndiswrapper.)

did not have problem linksys wrt54gl ap @ home nor did have windows xp on school ap.

lspci output:
code:
03:02.0 network controller: broadcom corporation bcm4306 802.11b/g wireless lan controller (rev 03)                                                                      subsystem: hewlett-packard company device 12f8                                   control: i/o- mem+ busmaster+ speccycle- memwinv- vgasnoop- parerr- stepping- serr- fastb2b- disintx-                                                            status: cap- 66mhz- udf- fastb2b- parerr- devsel=fast >tabort- <tabort- <mabort- >serr- <perr- intx-         latency: 64         interrupt: pin routed irq 21         region 0: memory @ b0200000 (32-bit, non-prefetchable) [size=8k]         kernel driver in use: b43-pci-bridge         kernel modules: ssb
iwconfig output:
code:
wlan0     ieee 802.11bg  essid:"anyu"           mode:managed  frequency:2.462 ghz  access point: 00:16:9d:cd:74:e0           bit rate=11 mb/s   tx-power=20 dbm           retry min limit:7   rts thr:off   fragment thr=2352 b           power management:off           link quality=71/100  signal level:-51 dbm  noise level=-67 dbm           rx invalid nwid:0  rx invalid crypt:0  rx invalid frag:0           tx excessive retries:0  invalid misc:0   missed beacon:0
ifconfig output:
code:
wlan0     link encap:ethernet  hwaddr 00:90:4b:ec:a9:c8           inet addr:172.29.82.220  bcast:172.29.83.255  mask:255.255.252.0           inet6 addr: fe80::290:4bff:feec:a9c8/64 scope:link           broadcast running multicast  mtu:1500  metric:1           rx packets:116050 errors:0 dropped:0 overruns:0 frame:0           tx packets:61063 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000           rx bytes:121760603 (121.7 mb)  tx bytes:7354656 (7.3 mb)
this first time running linux on own box in 4 years i'm little rusty!

id tell use b43 or openfwwf open source variant. there broadcom wireless reference in signature site ayuthia wrote (another ubuntu user). should lot!!!


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [kubuntu] have to keep disconnecting and reconnecting w/bcm43xx driver


Ubuntu

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more