Skip to main content

Thread: Error 17 - Cannot mount

-

hey, when grub , hit ubuntu im getting error 17.. im booting usb stick , im not sure change (hd0,0) thing to..
here sudo fdisk -l

disk /dev/sda: 250.0 gb, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
units = cylinders of 16065 * 512 = 8225280 bytes
disk identifier: 0x3ff80c2c

device boot start end blocks id system
/dev/sda1 1 1561 12538701 7 hpfs/ntfs
/dev/sda2 * 1562 30402 231657472 7 hpfs/ntfs

disk /dev/sdb: 4009 mb, 4009754624 bytes
255 heads, 63 sectors/track, 487 cylinders
units = cylinders of 16065 * 512 = 8225280 bytes
disk identifier: 0xc3072e18

device boot start end blocks id system
/dev/sdb1 * 1 459 3686886 83 linux
/dev/sdb2 460 487 224910 5 yextended
/dev/sdb5 460 487 224878+ 82 linux swap / solaris

ideas? lot.

you'll want set grub on (sdb). google "reinstall grub livecd ubuntu"

careful not mess mbr on hdd though. might want disconnect hdd while (if possible).

i'm kinda guessing you've got install of ubuntu on hdd?
can select boot device pressing f12 @ boot.(this works if it's enabled bios), , on machines it's f8 or f10 or combination of buttons. check in bios setup.


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support General Help [ubuntu] Error 17 - Cannot mount


Ubuntu

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more