Controlling an actuator via seeed motor shield

-

hi everyone,

i trying wire actuator motor shield off of arduino uno. having issues figuring out how hook actuator motor shield. have been searching through tutorials, haven't found directly relates project.

would better off buying figelli's lac board?

any or guidance appreciated!

actuator
http://store.firgelli.com/firgelli_l12_p_p/l12-p.htm

motor shield
http://www.seeedstudio.com/depot/motor-shield-p-913.html

well don't believe arduino specific, perhaps try posting type of question in motors section next time? i'm not trying mean/rude. you'd better support in right area all. posted here accident too. lol

but don't quite know issue you're having. plug on actuator doesn't fit shield?

also have seen these pages?

http://www.seeedstudio.com/wiki/motor_shield_v1.0

&

http://www.firgelli.com/pdf/l12_datasheet.pdf

you should able locate pinouts there and, if necessary, may need make custom plug.


Arduino Forum > Using Arduino > Motors, Mechanics, and Power (Moderator: fabioc84) > Controlling an actuator via seeed motor shield


arduino

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more