Position sensor LCD indicator using arduino

-

hi, guys.
i hoping build lcd indicator position sensor.
i have position sensor one.
https://www.flickr.com/photos/34955071@n02/14259851826/
i got sensor turbocharger.  this sensor used in turbocharger tell how turbocharger opened , closed air intake.
i need know in percentage(%), how turbocharger opened or closed.
so, using position sensor, hope have information in percentage 0%(fully closed) ~ 100%(fully opened).
this position sensor moves this.
https://www.flickr.com/photos/34955071@n02/14303154253/
between moving range, there must digital feedback sensor.
i think arduino read these signals position sensor , tell lcd show open or close variation status in percentage.
the pins of position sensor looks this.
https://www.flickr.com/photos/34955071@n02/14282368264/
and, pin information.
pin #1)   dc:5v
pin #2)   ground
pin #3)   single (voltage) dc
pin #4)   dc:5v
pin #5)   ground
pin #6)   single (voltage) dc
i don't have knowledge how connect position sensor arduino , read signal , use real time lcd display.
please advise me guys how should it. school project. life depends on project.



Arduino Forum > Using Arduino > General Electronics > Position sensor LCD indicator using arduino


arduino

Comments

Post a Comment

Popular posts from this blog

opencv3, tbb and rasp pi 2 - Raspberry Pi Forums

-
Image
has installed opencv 3.0.0 tbb enabled on latest rasperian on pi 2? followed guide here viewtopic.php?f=28&t=110025&p=761255&hi ... v3#p761255 differences made enable tbb via cmake... added build , tbb options shown.. cmake -d cmake_build_type=release -d build_tbb=on -d with_tbb=on -d cmake_install_prefix=$(python3 -c "import sys; print(sys.prefix)") -d python_executable=$(which python3) .. patched current, dependencies installed far can tell.. cmake reports going install , old version of tbb... -- use tbb: yes (ver 4.1 interface 6102) make process fails linking problem don't understand fully, [ 66%] built target opencv_features2d scanning dependencies of target opencv_test_flann ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::task_group_context::cancel_group_execution()' ../../lib/libopencv_imgproc.so.3.0.0: undefined reference `tbb::interface5::internal::task_base::destroy(tbb::task&)...
Read more

small ethernet problem - Raspberry Pi Forums

-
hello, after conventional installation raspbian noobs v 1.4 raspberry pi 2 . how can configure internet connection on raspberry me download apt. (my ethernet cable connected directly ethernet switch (i'm @ university)) attached configuration of pc internet connection. http://i.imgur.com/budyoeb.jpg thank much, google configuring rpi static ip address. use same ip numbers see on pc. not try have both pc , rpi connected network @ same time. raspberrypi
Read more

Multithumb configuration params not working? - Joomla! Forum - community, help and support

-
hi, i've installed multithumb 1.1 on joomla 1.011 site , works fine in basic set-up (and jce-editor). except when try tweaking mambot params, things stop working. specifically: if use "only in these categories" setting , fill in categoryname, e.g. "news", pop-ups/thumbnails stop working, categories, including "news". if use "not in these categories" these categories still use pop-ups. if select "use thumbnails" "no" not no thumbnails no pop-ups anymore. so way use multithumb selectively use optioni "apply content {multithumb}", bit cumbersome. there more people having these issues? hi bikey, i having issues bit different - yet same.  saying have way set configuration plug-in.  not know how find cong this.  if can maybe read posting - don't bore process.  jce editor - have not installed - still using default html editor - cant recall name.  why not see config file? anyway - find if use static page , pass com...
Read more